Readers ask: How To Sew A Lined Valance With Separate Fabric For Bottom Border?

How to Make a Window Valance

Valances are a great way to personalize a room and add instant style, and they’re super easy to make. Today, I’m showing you how to make a window valance (the quick and easy way! ), via video. Valances are a great solution if you want a quick project that uses very little fabric, and they’re ideal on windows where long drapes would get in the way.

Supplies Needed

You’ll need the following supplies to make a window valance. Use the measurement guides below to figure out how much fabric you’ll need. If you’re using a thinner fabric that lets a lot of light in, you might need to use blackout lining instead of or in addition to the regular lining.

Measuring and Cutting the Fabric

Measure your window and cut out the curtain and lining fabrics. You’ll need to know how big you want your valance to be in order to cut your fabric. The most important thing to remember is that your curtain and lining fabrics will be the same HEIGHT.

Sewing the Valance Together

Sew down both sides of the valance with coordinating thread and a 1/2u2033 seam allowance, then press the seams smooth and flat with a hot iron. This gives your valance a nice finished edge while also hiding the contrasting lining from the front.

Finishing the Top and Bottom of the Valance

After you’ve finished the sides, you’ll need a sewing gauge and a hot iron to finish the top and bottom of the valance. Fold the fabric (both the curtain and lining fabrics) down 1/2u2033 and iron in place.

We recommend reading:  How To Make A Durag?

Adding Blackout Lining (Optional)

Use a blackout lining to make your valance opaque. Cut a rectangle of blackout lining to the dimensions marked by the red dotted lines below, sew the top hem in place, and then finish the backside with hemmed edges.

Adding a Rod Pocket to the Window Valance

One of the quickest and easiest ways to hang a fabric valance is to use a rod. I strongly recommend using your actual curtain rod to determine the placement and size of your rod pocket. Run the valance through your sewing machine one last time along the line you just drew to make a perfectly fitting pocket.

How do you make layered valances?

How to Make a Valance with Two Layers

  1. Measure the length and width of the curtain rod on which the valance will hang.
  2. Cut the fabric pieces using the length and width measurements.
  3. Thread your sewing machine and bobbin with the matching thread.
  4. Hem the width edges of both pieces of fabric by turning under 1/2 inch along each edge.

How do you sew lined drapery panels?

  1. Measure the length of the curtain and lining panels from the floor to the desired height of the curtain rod.
  2. Fold and Press Hem. Place fabric on ironing board wrong-side-up.
  3. Insert Weights and Sew Hem.
  4. Hem Lining.

How much fabric do I need for a valance?

The obvious answer is that it depends, but you should expect to need between 1-1/2 and 5 yards of face fabric for a standard 36- to 40-inch window, and about 2-1/2 to 8 yards of face fabric for double-wide windows (roughly 70 to 80 inches wide).

We recommend reading:  Readers ask: How To Sew A Dinning Room Chair Cover?

How do you hem a valance?

To make the side hem, measure 12 inches along the length of the fabric, fold with wrong sides facing each other and press with your iron, then sew the hem on your sewing machine.

How do you make scalloped edge valances?

Sew a half-inch seam along both of the fabric’s short ends, as well as a half-inch seam along the scalloped edge. Sew a second half-inch seam on top of the first seam along the scalloped edge for reinforcement.

How do you make a box pleat valance?

Pleating your Box Pleat Valance

  1. Mark the center of your center pleat with a pin.
  2. Measure 23.5u2032u2032 from the right side of the toile section to the center of the valance.
  3. Fold right toile section at 23.5u2032u2032 wide to begin center pleat. 12u2032u2032 was allowed for the center pleat.

How can I make my curtains shorter without cutting them?

If your curtains are too long, sew a hem to shorten them without cutting them to length, allowing you to keep the fabric if you want to. Another way to shorten curtains is to use a folded design with buttons as fasteners. Folding the curtain hem up creates a double hem.

How do you join two curtains without sewing?

Fabric staplers shaped like pliers with fine wire staples provide enough support to seam two or more panels together without snagging the fabric, or purchase iron-on fusible strips that bond overlapping side edges for a sew-free finish from a fabric store or hobby shop.

Is it OK if curtains don’t touch the floor?

So, should curtains reach the floor? In most cases, yes; however, when choosing window treatments, whether drapes, blinds, or shades, it’s important to consider every aspect of style and function so you can choose the best option for your windows and home.

We recommend reading:  How To Knit Lace Stitches?

How much shorter should curtain lining be?

Regular lining should be 7.5cm (3″) shorter than the curtain fabric, while thermal lining is too bulky to make a double hem, so it should be 17.5cm (678″) shorter.

How do you sew two lined curtains together?

Place two curtain panels right sides together, top and bottom hems matching, and pin along one long side. Cut off the hem on that side with scissors or a rotary cutter and mat, cutting through both panels and the top and bottom hems. Remove the pins.

Leave a Reply

Your email address will not be published. Required fields are marked *